How to clean the toilet from rust and plaque?

A clean toilet always looks beautiful, but rust often occurs even with regular cleaning. To clean the toilet from rust and plaque with your own hands, you can use improvised means, it is not necessary to purchase expensive chemicals.

To clean the toilet from rust, you need to understand what it comes from. Rusty streaks and plaque can appear as a result of several main reasons:

• A huge role is played by the quality of water, which usually also includes impurities of various substances, for example, iron. An additional factor may be a leaking tank. This results in rust spots.
• It is worth paying attention to the pipes, namely what material they are made of. If the plumbing is made from non-galvanized pipes, then rust forms in them, which gets inside the toilet with water and leaves rusty streaks.
• The roughness of the toilet bowl plays an important role. Smooth surfaces are practically not affected by rust, since it is difficult for it to cling to them. Increased roughness contributes to the rapid formation of rust.Experts recommend giving preference to porcelain products in comparison with faience.

If it is not possible to purchase a brand new toilet, then you should think about high-quality cleaning of the old one. Experts recommend many ways to wash the toilet from the inside at home. Let's start with special tools.

Powder products are affordable, so everyone can afford them. The disadvantage of abrasive products is that they require a lot of effort so that they can be used to wipe off various kinds of dirt.

The powder should be applied to the contaminated surface, and then rubbed strongly with a rag until the plaque is eliminated. This can take a lot of time and effort.

This chemistry is considered more effective than the use of powder products. Alkalis do not require special efforts, since they dissolve any kind of pollution well, including rust. They must be applied to the contaminated area and left for a while so that the product comes into contact with rust. Then easily remove.

The advantage of using such chemistry is that it does not spoil the surface of the product. After using it scratches do not appear, and roughness does not increase.

In terms of their effect on rust, acids are in many ways similar to alkaline agents, but are more effective. Experts do not recommend their frequent use. They are useful for removing very dirty toilet bowls.

Acid should be applied to the affected area for just a few minutes.because it works very fast. After cleaning, the product should be thoroughly rinsed with water. With prolonged use of acid, not only rust marks can be removed, but also the enamel coating. The toilet becomes rough and loses its attractive appearance. You should look at the action of the acid, and at the right time to eliminate it.

Stubborn rust is perfectly handled by the tools that are always in the house. Folk methods are not inferior in the effectiveness of household chemicals, and are also safe and inexpensive.

It is sold dry. Oxalic acid should be poured a little on a rag and carefully rub the place of contamination on the toilet. To protect the skin of the hands from acid corrosion, all actions must be carried out with gloves.

The use of oxalic acid in the fight against rust is one of the most effective. Rusty streaks begin to dissolve instantly.The advantage of using oxalic acid is that it dissolves very quickly on the surface of the rag and no longer damages the surface of the plumbing.

This substance is used for batteries, so it is familiar to men. It belongs to strong acids, so it is also perfect for removing rust. It should be applied to the dirt for 10-20 minutes. Time should be adjusted depending on the age of rust.

This tool belongs to acids, therefore it is effectively used to eliminate stubborn dirt in the toilet bowl. Acetic essence must be applied to the rust and left for 30 minutes. Citric acid is a great alternative. Don't use regular vinegar., since it will not have the necessary effect on the surface of the plumbing.

Known drinks will help with rust removal. It is necessary to take a rag, moisten it well with a drink and put it on a contaminated place for about half an hour. Next, you need to rub the affected area a little for effectiveness and rinse with water.

This substance is quite strong and dangerous for humans, so all actions for cleaning the toilet should be performed carefully and always with rubber gloves. Do not ignore the respirator, since hydrochloric acid vapor can be very harmful to your health.

One toilet will require approximately 20 grams of acid.The agent must be applied to the surface of the plumbing and left for about 20 minutes, then rinse thoroughly.

Such a tandem allows you to quickly eliminate rust. When preparing the solution, it is necessary to adhere to a ratio of 5: 100. The mixture should be applied to contaminated areas and left for half an hour. After that, rub the affected areas with a brush and rinse thoroughly with water.

In the fight against rust and old streaks, whiteness will help to cope. The product must be poured into the toilet and left overnight. It is very important that the tank does not leak, and also do not flush the water. Already in the morning there will be no trace of urinary pollution, and rust will be easily removed.

After removing rust and plaque, every housewife wants to maintain an attractive whiteness for as long as possible. To prevent the appearance of rusty streaks and various kinds of pollution, you need to follow some recommendations of experts:

• Make sure the tank is not leaking. If you constantly run a trickle of water on the surface of the toilet, this will lead to deposits that will become more distinct over time. It is enough to adjust the toilet bowl float to eliminate this problem.
• The use of special tablets can slow down the process of rust formation. They need to be thrown into a tank of water, where they dissolve well. The composition of these tablets includes special substances that, when they get on the walls of the toilet bowl when flushed, prevent the formation of rusty streaks. Additionally, they provide a pleasant aroma.
• Using a water filter is an effective method to reduce water impurities that often settle on the surface of plumbing fixtures.The disadvantage of this method lies in its high cost. Not everyone can afford to buy such a filter.

Keeping your plumbing fixtures clean will help prevent the formation of plaque and stone. It is necessary to clean the drain tank regularly, as deposits accumulate in it. This procedure should be carried out at least once every six months.

When cleaning the toilet you need to use special gels and disinfectants. They must be applied evenly along the walls of the product, both internal and external. To clean the toilet inside, it is worth enlisting a brush. To thoroughly clean the sanitary ware in hard-to-reach places (near the lid attachment or under the toilet rim), you should use a toothbrush. You can use wet wipes to clean the seat and lid.

The neck of the toilet bowl must be filled with gel and left for half an hour. This will allow the dirt to get wet, and then with the help of a brush it can be easily and quickly removed. If you need to eliminate old traces of rust, then you need to remove the water with a plunger, and then just fill it with gel.

You can use paper towels or napkins to clean the outside of the toilet. It is enough to apply a disinfectant to the surface, thoroughly wipe the entire product with a damp towel.

How to clean the toilet from plaque and rust, see the following video.